Setting Bevel Angle--Pull the bevel lock knob and adjust the band saw to the desired angle by turning the handwheel, then push in the bevel lock to secure. Do not feed the work piece too rapidly, Remove the blade guard by loosening the two 2 mounting screws with a phillips screwdriver lifting the blade guard upward. Page 27 4. Loosen the setscrew which locks the blade guide support and push the support Repeat for lower blade guide support. Loosen the setscrew which locks the upper back up bearing and push the bearing back.
Repeat procedure for lower back up bear- ing. The align merit steps must be followed for proper tension, and bearing adjustments for each different The set of the teeth and the sharpened edge of the teeth would be damaged. To insure the backup bearing is properly porting the blade, push the bearing toward the blade until it almost touches wheel, by hand, checking the backup bearing to make sure it is not turning.
Page 31 3. Mount the front table to the base as follows: a. Makesurefronttablelatchesarepositioned high as they will go. Hold the front edge of the table. Position the rear edge of the table so that the two flat springs slip under the two tabs on the rear table. Adjust the front table so it is the same height as the rear table as follows: a, Lay a straight edge across front table to rear table.
Gentlytap the fronttable down until it is in line with the rear table, c. Always remove the yellow key and keep it in a safe place. To remove yellow key, hold thumb on the end of red lever to keep switch in "Off" Turn handwhee4 counter-clockwise the tilt angle of the blade. The digital display will read out the angle of the blade to the table.
A band saw is basically a "curve cutting" machine. It is not capable of doing inside cutting. Your Craftsman Band Saw is not only capable of the usual band saw operations, but it can be converted into a sander as well. NOTE: The sanding bett cuts very rapidly. Practice with some scraps of wood first before you attempt to sand your actual workpiece.
Page Maintenance "L" wrench that has a 4-inch leg, reach between the spokes of the lower wheel to the capscrews. Adjust the capscrews the bevel action is smooth and the saw wilt hold its position before the bevel lock is locked. Page Troubleshooting Blade does not run in Lower positioned the approximate center shaft. Belt too loose. Band Saw slows down when cutting. Cutting Duil blade. Overloading Blades breaking. Kink cutting Page Low Voltage Repair service is available at your nearest Sears store.
Do not use other appliances same circuit when using the saw. Increase wire sizes, or reduce length of wiring. See "Motor Specifications Requirements" 3. Request a voltage check from the power company. Page 41 - Replace battery. Battery is 6 volt, size J. Display should - Reset bevel zero reference. Wrong display function change when blade speed is changed. Encoder or digital display defective.
Display changes back 1. Slight variations and forth between in blade speed. Description Table, Rear Model This manual is also suitable for: Show all Print page 1 Print document 53 pages.
Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account?
Sign up! Restore password. Upload manual. KNOB 8. As soon as you stop cutting, the bear- ings should stop rotating. Turn the thrust bearing The wing screw keeps the table in alignment. Screw it into the tapped hole underneath the front edge of the table. Page 17 3. To turn machine PUSH lever in. Never leave the machine unattended until it has come to a complete stop. To lock switch in OFF position. Page 19 9. Remove the blade guard, cover, blade, and the upper guide assembly.
Attach sanding platen guide with same screw that held the upper blade guide assembly. Do not tighten the screw at this time. On the smooth side of the sanding belt, you will find "directional arrow", The belt Unlike a saw, it is not capable of doing inside cutting.
Defective On-Off switch, 1. Replace defective parts before using Defective switch Page Parts List "! Be sure provide pertinent facts when Print page 1 Print document 28 pages.
Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL.
0コメント